LAMPING OPTIONS
SPECIFICATIONS
CATALOG NUMBER
SPECIFICATIONS
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
22
46 5th Street, Berk
eley
, CA 94
710
• T
el: 510.845.27
60
• Fax: 510
.845.277
6
• Email:
[email protected] • PeerlessLighting.com3
⁄8”
Type: ________________________
Project: ______________________
1
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightline” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx
Direct T8
LLMS Lightline Symmetric
Examples: LLMS S 1 32 WPB 8FT R8 120 GEB10 1SE EC SCT L/LP C100
Surface LLMS
Lightline Symmetric
Direct
Direct T8
Construction
Extruded aluminum housing forms a 3
5
⁄8” x 4
1
⁄16”
rectangular profile. Die-cast aluminum end caps
mechanically attach with no exposed fasteners.
Shielding
Arc-shaped, parabolic low iridescent semi-specular
or white painted aluminum louver.
Reflectors
High reflectance white painted reflector system.
Finish
Satin anodized finish consists of satin anodized
housing with end caps painted to match. Custom
colors available, consult factory.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Luminaire Length
4’, 8’ and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’, and 12’. For total
luminaire length, add
7
⁄8” for each end cap. Using
internal joiners, 4’, 8’ and 12’ sections can be joined
to form longer rows.
__________ __________ __________ __________ __________ _________ __________ __________ __________ __________
Luminaire
LLMS
Mounting Type
S Surface
# of Lamps in
Cross Section
1
Lamp Type
32 32W T8
Bae
SSB Semi specular
bae
WPB White painted
bae
Luminaire
Row
Length
X FT
(4’ increments)
Maximum
Section
Length
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
Voltage
120
277
347
Ballast Type
GEB10 <10% THD Electronic
ADEZ
1
Advance Mark 10 dim
DMHL3D
1
Lutron Hi-Lume dim
ADZT
1
Advance Mark 7 0-10V dim
Reference Ballast Wizard on website
or consult factory for other options.
# of Emergency
Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
______________ ________________ ________________ ______________ _________________________________
Emergency Type
2
(Blank) None
EC Emergency circuit
EL
1
Emergency battery pack
EN
1
Emergency battery pack
w/night light circuit
Switching
SCT Single circuit
Lamp Color
L/LP No lamp
L/LPE No lamp. Wired
for energy saving
lamps.
LP830 3000K 80+ CRI
LP835 3500K 80+ CRI
LP841 4100K 80+ CRI
Reference Lamp Chart on
website or consult factory
for other options.
Finish
C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish
Options
DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NEPP5D nLight enabled control module per row/zone
NYC New York City code
XXXX Integrated sensor; choose options and obtain code on page 2
LLMS S
3
5
⁄8”
4
1
⁄16”
Notes:
1 Not available in 347V
2 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified
Commentaires sur ces manuels